WD-8018埋弧焊用燒結焊劑WD-8018 SAW FLUX
符合標準：GB/T17854－1999AWSA5.9M-2006ER2209?認證機構：CCS
所屬分類：
· 不銹鋼焊劑
咨詢熱線：
- 產品描述
-
- 商品名稱: WD-8018埋弧焊用燒結焊劑WD-8018 SAW FLUX
- 商品編號: 1057227672272068608
符合標準：GB/T17854－1999AWSA5.9M-2006ER2209?認證機構：CCS
符合標準：
GB/T 17854－1999 AWS A5.9M-2006 ER2209
認證機構：CCS
說明：WD-8018 是氟堿型堿性燒結焊劑，堿度約為2.5（BIIW），為乳黃色球形顆粒，直流施焊時焊絲接正極，最大焊接電流可達1200A，粒度為10～50目。該焊劑與焊絲ER2209配套焊接，熔敷金屬純凈，燒損元素較少，具有較高的抗拉強度和屈服強度；實驗數據滿足美國標準(AWS)，有比較高的鐵素體含量，焊后渣殼翹起，窄間隙脫渣容易，焊縫成形美觀，電弧燃燒穩定，抗吸潮性好，顆粒強度高，松裝密度小，焊接過程中焊劑消耗量少。
用途：可用于石油化工設備、海水與廢水處理設備、輸油氣管線、化工用船舶焊接。
焊劑參考成分（%）：
焊縫金屬力學性能典型值：
熔敷金屬化學金屬成分：
注意事項：
1、焊劑如果受潮，在使用前須經300~350℃烘焙2小時。
2、焊接處須清除鐵銹、油污、水分等雜質。
WD-8018 Agglomerated Flux For S.A. WeldingStandards: GB/T 17854－1999 AWS A5.9M-2006 ER2209Approvals: CCSIntroductionWD-8018 is an agglomerated fluoride-basic type flux with a basicity index of BIIW 2.5. The flux is yellow spherical granular. WD-8018 can be welded with DC at up to 1200A,connect the welding wire to the positive terminal when with DC. Grain size is from 10 to 50 mesh. This flux is for matching with ER2209 welding wire, deposited metal is pure, burning loss is low, has high tensile strength and yield strength; Test result meets AWS standard, has high content of delta ferrite, slag removal is easy in the narrow gap. Bead appearance is beautiful, burn-out of the arc is stable, slag is easy to remove. The flux has low moisture pick-up and granular stability. As the bulk density is low, its consumption rate are few.ApplicationsWelding of petrochemical industry equipments, treatment equipments of seawater and waste water, oil and gas pipelines, ships for chemical engineering.Main Constituents (%)
Typical mechanical property of deposited metal
Typical chemical composition of deposited metal (%)
Notice:1. Flux should be redried at 300~350°C for 2 hours.2. All dust, oil and rust should be removed關鍵詞:- 焊劑
- 焊接
- 金屬
- 焊縫
- 焊絲
- er2209
- 標準
- aws
- 強度
上一頁
下一頁